Expert Answers about Chevrolet Drop Hitch

• How to Prevent a 12 Inch Receiver Hitch Extension From Rattling in Receiver
• Adding an extension introduces another component in between the receiver and the ballmount or hitch accessory. Because of this, getting a certain amount of wobble is unavoidable. If you're using the extension for a hitch mounted accessory, you can use an anti-rattle device like part # BX88224. However, keep in mind that using an extender will lower the tongue weight capacity of your hitch by 50 percent. If you'll be towing, you'd be better off using a longer ball mount, if the longer...
  view full answer...


• Weight Distribution for a Car Trailer with a Channel Coupler 4 Inches Higher than the Trailer Frame
• The way I would go about this is to lower your coupler height or use a coupler similar to the Bulldog Collar-Lok Coupler w/ Pin - 2-5/16 inch Ball - Adjustable Channel Mount - 12,500 lbs, item # BD028585, and mount it so that the coupler is in the correct position to allow a weight distribution hitch to be used with the trailer and coupler. Make sure the coupler you select will accommodate the total weight of your trailer and the loads on it. You would then use a weight distribution system...
  view full answer...


• Troubleshooting Trailer with Fastway Weight Distribution Where Trailer Moves Forward and Back
• The Fastway weight distribution system part # FA94-00-1000 is the correct system rated for your tongue weight of 715 lbs so that leads me to believe you either have the spring bar tension maybe not fully dialed in or the trailer isn't sitting perfectly level. The play in the hitch you mentioned would not cause this issue. If you need more drop from your shank to allow your trailer to sit level we have the part # FA92-02-4214 for up to a 5-1/4 inch drop or part # FA92-02-4315 for up to...
  view full answer...


• Troubleshooting Pin Removal for Hitch Ball Change on Andersen Rapid Hitch Ball Mount
• It sounds like the Rapid Hitch Adjustable Aluminum Ball Mount Kit - 2 Zinc Balls - 5-1/2" Drop, 6-1/2" Rise # AM3411 has dirt or debris binding the pin. Since this pin simply drops in place as you can see in the attached video, the best way to remove the pin is to use some penetrating oil around that pin and then using movement to allow the oil to find its way to the bound location. I recommend using a rubber mallet to give vibration and movement to the pin while trying to twist the hitch...
  view full answer...


• Choosing the Correct Adjustable Shank for Weight Distribution System On a 2019 GMC Sierra 2500
• It sounds like the shank on the weight distribution system you have does not offer enough drop adjustment, which is causing your trailer to not be level. Depending on the weight distribution system you have you can purchase a different shank like the Curt Weight Distribution Shank # 17120 that will allow up to 5-3/4 inch drop for a trunnion system to help get your trailer level. I included an article that goes over how to measure for the correct rise/drop for your setup. If you can...
  view full answer...


• Unable to Get B&W Companion Base To Fit a 2022 GMC Sierra 3500 With Factory Prep/Puck System
• The pucks on your 2022 GMC Sierra 3500 will not be adjustable as they are a fixed part under the bed. You should be able to loosen up the cotter pins and castle nuts on the Replacement Base for B&W Companion # BWRVB3710 to get the hitch to drop into the mounting points on your bed. while they normally will drop into most the pucks without adjustment they do offer some adjustment to ensure a proper fit. Please let me know if that does not work for your base and if you can inspect the...
  view full answer...


• Troubleshooting Rear End Sag or Squat on 2015 Nissan Quest
• Suspension Enhancement would assist with keeping your vehicle from dropping in the rear. Unfortunately there is not currently any vehicle suspension enhancement from any of our manufacturers that is confirmed to fit your 2015 Nissan Quest. Unfortunately that means air springs are currently not an option to help level your vehicle under load. You're best option is to work on your weight distribution system head adjustment to give you less drop at your vehicle and still give you the support...
  view full answer...


• Troubleshooting Fit of Draw-Tite # 75673 on a 2011 Subaru Outback
• The Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2" # 75673 is a confirmed fit for your 2011 Outback Wagon as long as it isn't the sport model. It is very rare for a hitch not to fit and we have never had one that isn't dropped or bent that will not fit in the way shown on your photo. If it is not bent from being dropped, then there is a chance it was a manufacturer defect and should be returned. I've attached the installation details that show drilling is required...
  view full answer...


• Troubleshooting 2 Inch Ball Mount that Fits Too Tight In Vehicle Receiver
• The Curt Class III Ball Mount with 2" Ball - 2" Drop - 7,500 lbs # C45036 sounds like it may have a little too much powder coat or something to cause resistance like you stated. Alternatively it could be the receiver side as well but it seems odd that the Brophy Ball Mount for 2" Hitch - 3/4" Rise, 2" Drop - 13-1/4" Long - 10,000 lbs # BH20 fits if it were the receiver side. The # BH20 will work fine for your 7,500 lb capacity if you don't want to purchase another option. You can also...
  view full answer...


• How Do I Remove a Stuck Pin on the B&W Tow & Stow # BWTS20040B?
• Sorry to hear about your hitch! In order to determine the best course of action with your hitch, do you have the manufacturer/model of hitch that you have? Thanks so much!
  view full answer...


• Setting Up Reese Steadi-Flex Weight Distribution
• Be sure that the top of the ball is ½” to 1” higher than the top of the coupler before hooking up (trailer/truck level). If I understand correctly, 7 1/8” is the height now – that will not work. The shank can be used in the rise and/or drop positions as needed, so if you have the ball in the drop position and it's already at its maximum height, you can remove the weight distributing head, flip the shank over into the rise position and install the head in the lowest set of holes. It...
  view full answer...


• Will The Cushioned Ball Mount # AMSC6 Help Reduce Bounce On Coachmen Clipper Trailer
• The item you selected, Cushioned Ball Mount, part # AMSC6, will help a bit in any noise or bounce of the drawbar. The recommended rise and drop for a ball mount on your 2011 Volkswagen Routan is 2 inch rise and 4 inch drop. You will need to use Cushioned Ball Mount, part # AMSC4. Another thing that can contribute to the rough ride you are feeling is low tongue weight. The tongue weight on your Coachmen Clipper 1285 SST may be very low. Proper loading of the trailer, with heavier items...
  view full answer...


• How to Level Trailer with Weight Distribution System
• You may be able to level your hitched trailer by substituting a different shank for your weight distribution system. I have included a link to our main page for weight distribution shanks. The Reese shank that has the most drop for a trunnion bar system is # RP3344. At most it is capable of 7-5/8 inches of drop when used with a trunnion bar system. You will want to measure your truck from the ground to the ballmount when your truck and trailer are on level ground. I have included a link...
  view full answer...


• How to Level Out a Truck and Trailer with Different Heights With a Weight Distribution System
• With both your truck and trailer being on level ground, if you measured your truck from the ground to the ballmount and came up with 24 inches that is good. On the trailer side, if you again, measured from the level ground to the bottom of the coupler and came up with 18 inches then that is good as well. According to your calculations, the difference between the receiver and coupler height is 6 inches, therefore a 7 inch drop shank should work well. I have attached a FAQ article covering...
  view full answer...


• Stromberg Carlson Electric Trailer Jack Continues to Drop After Lowering
• It does indeed sound like the Stromberg Carlson Electric Trailer Jack part # SC63VR was damaged using the manual override feature without first engaging the switch. This would not be covered under warranty unfortunately so you will need to replace the jack. I recommend the Phoenix Electric Trailer Jack part # UF38-944040 which will be a nice upgrade. This jack offers some of the fastest speeds on the market and it has one of the best warranties available of ten years. I did a review video...
  view full answer...


• Is It Normal For Pucks To Be Tight When Installing A Demco Autoslide 5th Wheel Hitch
• It's definitely not unheard of for pucks to be a bit tight when trying to get the 5th wheel hitch into place, and that goes for pretty much any hitch brand. The solution is to loose the puck feet on the hitch a bit until you can get them to drop in easily and then retighten them when in place. For your Demco Autoslide 5th Wheel Hitch w/ Slider - 18K # DM8550024 you'll want to follow the steps Dave shows in the video I've attached below. He'll start talking about the puck feet around the...
  view full answer...


• Excessive Movement Between the Curt A20 5th Wheel Hitch and 5th Wheel Trailer King Pin
• First, make sure that the jaws are fully closing around the king pin and that they are locked into place. If not then that would be why you are experiencing so much movement. If they are fully closing and locking then it is possible that the movement is actually coming from somewhere else such as at the connection between the head and the center section or the feet and the OEM Ford mounts. There are some things you can look at on the hitch to determine if the jaws are not fully closing....
  view full answer...


• Troubleshooting Flat Tires When Towing Mini Cooper With 2011 Holiday Rambler
• First, before flat towing your 2011 Mini Cooper, be sure the tires are filled to the recommended psi and in good condition. More importantly, be certain your steering column is not locked; if your tires are unable to turn they would wear out quickly. If you think your safety cables may be an issue, and yours are shorter than 7', an option would be the Blue Ox Blue Ox 7' Safety Cables # BX88197. Another thing you could do is add an anti-rattle device such as the Blue Ox Hitch Receiver Immobilizer...
  view full answer...


• Troubleshooting Frozen Fastway DT Hitch
• For your Self-Locking, Adjustable 2-Ball Mount w Chrome Balls - 2" Hitch - 6" Drop, 7" Rise # DTALBM6600 or similar, you started with the right idea. Penetrating oil is your best bed to loosen corrosion and grime. If the lock doesn't free up your best bet is to use the Re-Keying Kit for DTLBM and DTALBM Series Self-Locking Aluminum Ball Mounts - 2 Locks # DTLBM02RK.
  view full answer...


• Why Does My Trailer Sway When Towed with One Vehicle But Not with Other Vehicle
• Most likely the reason your trailer is swaying when being towed by your 2005 Kia Sorento is because the trailer is not sitting level while being towed with this vehicle. You will want to pick a ball mount with the correct amount of rise/drop so that your trailer sits as level as possible. Typically a hitch ball mounted in a bumper will sit higher than a ball mount in a frame mounted hitch. For more info on that check out the help article I attached.
  view full answer...